Specification:Name: CPU Anti-Bending FrameMaterial: aluminum alloyColor: black, gray, red, blue (optional)Applicable: Only provide support for Intel 12th generation CPU, the motherboard CPU socket is LGA1700, and the chipset is H610 B660 Z690 seriesSize: Length 54mm Width 70mm Height 6mmWeight: main body 20g; overall 50gProduct description:Thermalright creates an anti-bend solution for Intel's Alder Lake processorsFor Intel's Alder Lake processors are prone to flexing and warping, a flaw with for the Intel LGA1700 CPU's latching system. In response to this problem, an "anti-bend frame" was developed, designed to prevent warping/bending of Alder Lake CPUs.The LGA1700-BCF, an aluminum frame that replaces the CPU mounting mechanism of the company's LGA1700 CPU socket. This frame fits around the processor and is secured with simple screws. The frame applies more even pressure to for Intel's Alder Lake processors, reducing the chance of warping. However, for Intel warns that this mounting solution could void your CPU warranty, so consumers should be aware of this.This LGA 1700 Anti-Bend Buckle adopts an all-aluminum CNC gold anodized sandblasting process, with an overall size of 70 x 54 x 6 mm and an overall weight of 50g. Its precise positioning can avoid the capacitors on the motherboard, and uses the original LOTES insulation protection pads, and also provides different color schemesCompared with the previous home-made brackets, this LGA 1700 anti-bending buckle is much more comprehensive in design and better quality. What's more, the price is very affordable. Z690, B660 and H610 motherboards can use this LGA 1700 anti-bending clip Feature:1. Comparison: Compared with other similar products, this product uses four side flat pressure instead of multi-point pressure, with accurate positioning, avoiding capacitance, which is conducive to CPU fixation;2. Insulation protection pad: The contact surface with the main board is flat bottom, and the original LOTES insulation protection pad of the same specification is used to reduce the pressure on the main board and further reduce the signal interference;3. Signal interference: The metal surface is raised to reduce the signal interference on the motherboard side;4. Materoal: This CPU orthotic device has two colors: black and red. It is made of anodized sand blasting all aluminum alloy CNC precision machining, uses the original insulation rubber pad, and is fixed with hexagonal socket screws. It is easy to install and can reduce the penetration of silicone grease at the edge of the CPU;5. Description: Due to the design of the AMD Ryzen 7000 "special-shaped" CPU top cover, when installing the radiator, due to the installation pressure, there will be excess thermal conductive silicone grease extruded, which will accumulate at the Gap of the AMD Ryzen 7000 CPU, which may be difficult to remove, or even leak into the capacitor, which may pose a safety hazard. for AMD RYZEN 7000 Origin: Mainland ChinaModel Number: CPU BracketType: CPU HolderColor: Black, red (optional)Properties: No silicone grease, with silicone grease (optional)Material: Aluminum alloyProcess: CNC anode sandingFixing accessories: L-type screwdriverSize: 70x54x6mm/2.76x2.13x0.24inWeight: Body 20g, overall 55gInstallation process:1. Place the motherboard horizontally on the desktop and open the CPU clip2. Use the attached T20 Torx screwdriver to remove the upper part and put the lower fastener aside3. Put the CPU in4. Cover the improved snap on the CPU top cover and gently move it until it clicks into place5. Tighten the screws on the opposite angle by half a turn. Each screw takes half a turn in diagonal order until it is screwed on, will put pressure on the CPU unevenlyNote:Without thermal grease.Due to the different monitor and light effect, the actual color of the item might be slightly different from the color showed on the pictures. Thank you!Please allow 1-2cm measuring deviation due to manual measurement. |
